一、振動電機電路連接故障排除。

　　振動盤廠家的三相電壓不平衡主要表現為:(1)變壓器三相繞組有一相異常，傳輸電源電壓不對稱。(2)輸電線路長，導線截面尺寸不均勻，阻抗壓降不同，造成各相電壓不平衡。(3)電力、照明混合共用，其中單相負荷較多。比如家用電器、電爐、電焊機等。都過于集中在一相或兩相，導致各相電力負荷分布不均，供電電壓和電流不平衡。過載電機處于過載運行狀態，特別是啟動時，電機定子和轉子電流增大，產生熱量。時間稍長，振動電機容易出現繞組電流不平衡。

　　二、振動電機過載問題調查。

　　振動盤廠家的振動電機中的異物摩擦影響電機的正常運行。聯軸器零件歪斜，導致電機主軸錯位。潤滑油干燥或缺失導致軸承磨損電壓過高或過低，增加損耗。負載匹配不當，電機額定功率小于實際負載。電機地腳螺栓或部件固定螺栓松動，導致電機或部件移位。定子和轉子組故障、匝間短路、局部接地、開路等。，會導致定子繞組中的一個或兩個電流過大，從而嚴重不平衡三相電流。定子和轉子繞組故障的特點是內孔有灰塵、雜物和硬傷口，導致匝間短路。定子繞組的一相開路。定子繞組潮濕，有泄漏電流。軸承和轉子損壞變形，轉子和定子繞組相互摩擦。鼠籠式轉子繞組斷裂焊接，導致電流不穩定。

　　三、振動電機在使用中操作不當。

　　振動盤廠家的振動電機安裝人員將相線和零線反向連接。進線與接線盒碰撞，造成泄漏電流。開關、觸點和接頭的松動和氧化連接會導致缺相。頻繁啟動，啟動時間過長或過短，導致熔斷器斷相。長期使用，缺乏維護，使電機老化，局部絕緣退化。